Fire Extinguisher Recharge Near Me
A discharged or low-pressure fire extinguisher is a liability — and leaving it that way puts you out of compliance. Serviced Fire Equipment provides fast, professional fire extinguisher recharge services for businesses, contractors, and property managers throughout the Tampa Bay area.
Skip the $100+ service call. Drive to our St. Petersburg facility and we’ll recharge your extinguisher while you wait — or swap it out on the spot with the same type, brand, and quality, fully charged, tagged, and certified. Most recharges are done the same day. In most cases recharging is significantly more cost-effective than replacing a perfectly good extinguisher.
When Does a Fire Extinguisher Need to Be Recharged?
Even if a fire extinguisher looks full it may not be ready to perform in an emergency. You should have your extinguisher recharged:
- After any use — even if only partially discharged. A partially used extinguisher cannot be relied upon in an emergency
- If the pressure gauge is low or outside the green zone — pressure loss over time is common and often goes unnoticed
- If the safety pin or tamper seal is missing or damaged — indicates the unit may have been tampered with or partially discharged
- If annual inspection reveals leaks, corrosion, or worn components
- After the 6-year internal maintenance interval — stored pressure dry chemical units require internal inspection and recharge every 6 years per NFPA 10
- If the unit shows signs of physical damage — dents, corrosion, or a damaged valve can affect pressure retention
When in doubt bring it in — we’ll inspect it and tell you exactly what it needs.
Our Fire Extinguisher Recharge Process
We handle all recharges in-house using a structured process designed for safety, accuracy, and compliance with NFPA 10 standards.
- Initial Inspection — We evaluate pressure, physical condition, and overall functionality to determine the correct service
- Controlled Discharge — If needed, the unit is safely emptied of remaining agent
- Agent Refill — The correct extinguishing agent is added based on the unit type and manufacturer specifications
- Repressurization — The extinguisher is brought back to proper operating pressure
- Final Testing & Tagging — The unit is leak tested, pressure checked, tagged, and documented per NFPA 10 standards
If your unit needs a recharge we can also swap it out on the spot with a unit of similar condition that fits the same bracket — fully charged, tagged, and certified — so you never leave without compliant equipment. No extra trips, no downtime.
Types of Fire Extinguishers We Recharge
We recharge all common fire extinguisher types used in commercial, industrial, and residential settings including:
- ABC and BC dry chemical extinguishers — 2.5 lb, 5 lb, 10 lb, and 20 lb units
- Purple K (PK) dry chemical extinguishers — for flammable liquid and gas hazards
- CO₂ extinguishers — 5 lb, 10 lb, 15 lb, and 20 lb units. Larger cylinders charged at $1.75 per lb
- Class K kitchen extinguishers — required for commercial kitchens and food service facilities
- Clean agent extinguishers — Halotron, FM200, Halon, and Cleanguard systems
- Ansul Red Line extinguishers — pre-engineered suppression system cylinders
- Water extinguishers — 2.5 gallon pressurized water units
- Class D extinguishers — for combustible metal hazards
Please note: We no longer service foam extinguishers (AFFF and FFFP).
If you’re unsure what type of extinguisher you have, bring it in and we’ll identify it and recommend the correct service.
Fire Extinguisher Recharge Pricing
Walk-in pricing at our St. Petersburg facility. No service call fee, no trip charge.
| Extinguisher Type & Size | Walk-In Recharge Price |
|---|---|
| ABC, BC, PK Dry Chemical — 2.5 lb | $25.00 |
| ABC, BC, PK Dry Chemical — 5 lb | $35.00 |
| ABC, BC, PK Dry Chemical — 10 lb | $45.00 |
| ABC, BC, PK Dry Chemical — 20 lb | $55.00 |
| Water Extinguisher — 2.5 Gallon | $35.00 |
| Class K Kitchen — All Sizes | $195.00 (includes hydro if needed) |
| Class D — 30 lb | $210.00 |
| CO₂ — 5 lb | $35.00 (plus hydro if needed) |
| CO₂ — 10 lb | $45.00 (plus hydro if needed) |
| CO₂ — 15 lb | $60.00 (plus hydro if needed) |
How Long Does Fire Extinguisher Recharge Take?
Most walk-in fire extinguisher recharges are completed the same day at our St. Petersburg facility — often in under 10 minutes. Because everything is handled in-house by the same certified technicians there are no handoffs, no outsourcing, and no delays.
If you don’t want to wait at all we’ll swap your unit out on the spot with one of similar condition that fits the same bracket — fully charged, tagged, and certified. You’re back on the road in about 5 minutes.
For larger batches, specialty units like clean agent systems, or units requiring hydrostatic testing we’ll give you a clear timeline upfront. In most cases we can still do a same-day swap so you’re never left without compliant equipment.
How Much Does Fire Extinguisher Recharge Cost?
Recharge pricing at Serviced Fire Equipment ranges from $25 for a 2.5 lb ABC unit up to $195 for a Class K kitchen extinguisher — see the full pricing table above for all types and sizes.
In almost every case recharging is significantly more affordable than replacing a good extinguisher. And because you’re bringing it directly to our St. Petersburg facility you avoid the $100+ service call fee that most mobile companies charge just to show up — before they’ve touched a single unit.
For units requiring hydrostatic testing we’ll let you know upfront so there are no surprises. Call us at (727) 620-3473 with any questions about your specific unit.
NFPA 10 Fire Extinguisher Recharge Requirements
All fire extinguisher recharges at Serviced Fire Equipment are performed in full compliance with NFPA 10 — the Standard for Portable Fire Extinguishers — and the Florida Fire Prevention Code.
Under NFPA 10 fire extinguishers must be:
- Recharged immediately after any use — even partial discharge
- Maintained at proper pressure levels at all times
- Serviced during the 6-year internal maintenance interval
- Hydrostatically tested at required intervals depending on type
- Tagged and documented after every service with date, technician ID, and work performed
Failing to maintain proper recharge status puts your business out of compliance and leaves you exposed during fire marshal inspections, insurance audits, and OSHA reviews. Every recharge we perform is documented and tagged so you have a clear compliance record at all times.
Common Fire Extinguisher Recharge Mistakes to Avoid
These are the most common recharge-related mistakes we see from businesses and property managers — all of which are easy to avoid:
- Waiting too long after use — even a brief discharge means the unit must be professionally recharged before it can be relied upon again. Don’t put it back on the wall and assume it’s still good
- Assuming a gauge in the green means the unit is fully charged — gauges can be inaccurate, especially on older units. A professional recharge confirms actual agent levels
- Ignoring slow pressure loss — extinguishers lose pressure gradually over time. If the gauge has drifted even slightly it needs attention
- Attempting a DIY recharge — fire extinguisher recharging requires certified equipment, correct agents, and proper pressurization. An improperly recharged unit can fail or even rupture under pressure
- Delaying the 6-year internal maintenance — dry chemical extinguishers require internal inspection and recharge every 6 years regardless of whether they’ve been used. Many businesses miss this entirely
- Not keeping recharge records — documentation is required by NFPA 10 and expected during fire marshal inspections. Every recharge we perform is tagged and documented
Skip the $100+ Service Call – Walk-In Recharge Available
Most fire protection companies charge $100 or more just to show up — before they’ve recharged a single extinguisher. Then you wait days for scheduling, coordinate access, and manage the whole process on their timeline.
Our walk-in model eliminates all of that.
Drive to our St. Petersburg facility at 3200 62nd Ave N — just off I-275 — and we’ll recharge your extinguisher while you wait. No appointment, no service call fee, no delays. Most recharges are done in under 10 minutes.
Don’t want to wait at all? Pull up and swap out. We’ll exchange your discharged unit on the spot with one of similar condition that fits the same bracket — fully charged, tagged, and certified. You’re back on the road in about 5 minutes with a compliant extinguisher already mounted.
Customers from Clearwater, Largo, Pinellas Park, Tampa, and Palm Harbor make the drive specifically to avoid service call fees — and the savings add up fast.
Serving St. Petersburg and Surrounding Areas
Our St. Petersburg facility on 62nd Ave N is centrally located just off I-275 — making it an easy stop for businesses throughout Pinellas and Hillsborough County. We regularly serve customers coming from:
- St. Petersburg
- Clearwater — 20 minutes up I-275
- Largo — 15 minutes away
- Pinellas Park — 10 minutes away
- Tampa — 30 minutes across the bridge
- Dunedin — 25 minutes up US-19
- Palm Harbor — 30 minutes up US-19
- Bradenton — 45 minutes across the Skyway
Most customers tell us the drive is worth it the moment they see what they save compared to a mobile service call. For contractors and property managers making regular trips the savings add up fast.
Conveniently Located for Walk-In Service
Our St. Petersburg shop is centrally located and easy to access from anywhere in Pinellas County. Whether you’re dropping off a single extinguisher or multiple units, we make the process quick and straightforward.
Related Fire Extinguisher Services
In addition to recharge we offer a full range of fire extinguisher services — all handled in-house at our St. Petersburg facility:
- Fire extinguisher inspection and certification — $8 to $15 per unit
- CO₂ refill and recharge — fire extinguishers, kegerators, beverage systems, and industrial cylinders
- Hydrostatic testing — DOT-certified, performed entirely in-house
- SCBA hydrostatic testing — for fire departments, dive shops, and industrial operators
- Clean agent fire extinguisher service — Halotron, FM200, Halon, and Cleanguard
- Fire extinguisher rentals — by the unit, pallet, or gaylord
Everything can be handled in one visit so you leave fully compliant without extra trips.
NFPA 10 Fire Extinguisher Maintenance & Recharge Requirements
Complete reference for all required service intervals under NFPA 10 and DOT regulations — applicable to all commercial buildings in Florida:
| Extinguisher Type | Annual Inspection | 6-Year Internal Maintenance | Hydrostatic Testing | Recharge Cost at Our Facility |
|---|---|---|---|---|
| ABC Dry Chemical — 2.5 lb Most common general commercial type |
Every year — licensed technician required | Every 6 years — full disassembly, internal inspection, recharge | Every 12 years | $25.00 |
| ABC Dry Chemical — 5 lb | Every year | Every 6 years | Every 12 years | $35.00 |
| ABC Dry Chemical — 10 lb | Every year | Every 6 years | Every 12 years | $45.00 |
| ABC Dry Chemical — 20 lb | Every year | Every 6 years | Every 12 years | $55.00 |
| BC Dry Chemical (Sodium Bicarbonate) Class B and C fires only |
Every year | Every 6 years | Every 12 years | Same as ABC pricing |
| Purple K (PK) Dry Chemical Industrial and flammable liquid hazards |
Every year | Every 6 years | Every 12 years | Same as ABC pricing |
| CO₂ Extinguisher — 5 lb Electrical and server room applications |
Every year — cylinder must be weighed, gauge alone is unreliable | Not required — CO₂ units follow hydrostatic schedule only | Every 5 years | $35.00 plus hydro if needed |
| CO₂ Extinguisher — 10 lb | Every year — weigh cylinder | Not required | Every 5 years | $45.00 plus hydro if needed |
| CO₂ Extinguisher — 20 lb | Every year — weigh cylinder | Not required | Every 5 years | $70.00 plus hydro if needed |
| Class K Wet Chemical Required for commercial kitchens within 30 ft of cooking equipment |
Every year | Every 6 years | Every 5 years | $195.00 includes hydro if needed |
| Water and Water Mist Class A ordinary combustibles |
Every year | Every 6 years | Every 5 years | Call for quote |
| Clean Agent — Halotron, FM-200, Cleanguard Server rooms, medical facilities, sensitive electronics |
Every year — agent weight must be verified, gauge alone is unreliable | Per manufacturer specifications — typically every 6 years | Every 12 years | $130.00 + cost of missing agent |
| Ansul Red Line Cartridge-Operated Industrial, aviation, and high-hazard environments |
Every year — cartridge and agent cylinder inspected separately | Cartridge replaced per manufacturer interval — not standard 6-year | Every 12 years for agent cylinder | Call for quote |
Important Notes on NFPA 10 Compliance:
- After any discharge — even partial use — the unit must be professionally recharged before returning to service regardless of type or size
- CO₂ gauge readings are unreliable — CO₂ cylinders must be weighed against the nameplate weight to confirm charge level. A gauge reading in the green zone does not confirm the unit is properly charged
- Clean agent weight verification — same issue as CO₂. Weight is the only reliable confirmation of charge level for Halotron, FM-200, and Cleanguard units
- Hydrostatic test date past due — a cylinder past its DOT hydrostatic testing date cannot legally be recharged anywhere in the United States regardless of apparent condition
- 6-year maintenance is mandatory — the most commonly missed requirement. Required for all stored pressure dry chemical units regardless of whether the unit has ever been used
- All pricing above is at our St. Petersburg walk-in facility — no service call fee, no appointment needed
Questions about your specific extinguisher type or service interval? Call (727) 620-3473 or bring it in and we'll evaluate it on the spot.
Frequently Asked Questions — Fire Extinguisher Recharge
How much does it cost to recharge a fire extinguisher?
Recharge pricing at Serviced Fire Equipment starts at $25 for a 2.5 lb ABC dry chemical unit and ranges up to $195 for a Class K kitchen extinguisher. CO₂ recharges start at $35 for a 5 lb unit. See the full pricing table above for all types and sizes. Walk-in customers save significantly by avoiding the $100+ service call fee most mobile companies charge just to show up. Call (727) 620-3473 for a quote on your specific unit.
How long does fire extinguisher recharge take?
Most walk-in recharges are completed in under 10 minutes at our St. Petersburg facility. If you don't want to wait at all we'll swap your unit out on the spot with one of similar condition that fits the same bracket — fully charged, tagged, and certified. You're back on the road in about 5 minutes. Larger batches and specialty units like clean agent systems may take slightly longer but we'll give you a clear timeline upfront.
Can I recharge a fire extinguisher myself?
No — fire extinguisher recharging must be performed by a licensed technician using certified equipment. DIY recharging is not only non-compliant with NFPA 10 and Florida law but also dangerous. An improperly recharged unit can fail to discharge correctly in an emergency or rupture under pressure. Professional recharging ensures the correct agent, correct pressure, and proper certification tagging.
How often does a fire extinguisher need to be recharged?
A fire extinguisher must be recharged immediately after any use — even partial discharge. Beyond that, stored pressure dry chemical extinguishers require internal inspection and recharge every 6 years per NFPA 10 regardless of use. Units should also be recharged if pressure loss is detected during annual inspection or monthly visual checks.
What happens if you don't recharge a fire extinguisher after use?
A partially or fully discharged extinguisher that is put back in service without recharging is essentially useless in an emergency — and keeping it in service puts your business out of compliance with Florida fire code and NFPA 10. During a fire marshal inspection an unrecharge unit will result in a violation. Worse, in an actual fire emergency a discharged unit could cost lives. Bring it in immediately after any use and we'll have it recharged and back in service the same day.
Is it cheaper to recharge or replace a fire extinguisher?
In most cases recharging is significantly cheaper than replacing. A 10 lb ABC recharge costs $45 at our walk-in facility — a comparable new unit costs $60 to $100 or more. The exception is older units that are heavily corroded, past their hydrostatic testing life, or no longer serviceable — in those cases replacement makes more sense. We'll always give you an honest assessment and recommend the most cost-effective option. If replacement is needed we stock both refurbished and new units ready for immediate deployment.
What types of fire extinguishers do you recharge?
We recharge ABC, BC, and PK dry chemical extinguishers, CO₂ extinguishers, Class K kitchen units, clean agent systems (Halotron, FM200, Halon, Cleanguard), Ansul Red Line extinguishers, water extinguishers, and Class D units. Please note we no longer service foam extinguishers (AFFF and FFFP). If you're unsure what type you have bring it in and we'll identify it.
Do you offer a swap-out service?
Yes — this is one of our biggest differentiators. If you need your extinguisher back immediately we'll swap it out on the spot with a unit of similar condition that fits the same bracket — fully charged, tagged, and certified. No waiting, no extra trips. You pull up, swap out, and you're back on the road in about 5 minutes with a compliant extinguisher already mounted. This is especially popular with contractors and property managers who can't afford downtime.
Do I need an appointment for walk-in recharge service?
No appointment is needed. Simply drive to our St. Petersburg facility at 3200 62nd Ave N — just off I-275 — during business hours Monday through Friday and our certified technicians will take care of everything on the spot. No scheduling, no service call fee, no waiting on a technician. Customers from Clearwater, Largo, Tampa, and beyond make the drive regularly to take advantage of our walk-in service.
Does recharging a fire extinguisher reset the inspection date?
Yes. Every recharge we perform includes a new certification tag with the current date, technician ID, and work performed — resetting your annual inspection compliance clock. We can also upload your service records to the Brycer Compliance Portal if your property management or insurance provider requires digital documentation.
Authorized, Certified, and Verified Since 1999
Suppression Approved
Active Member
Get Your Fire Extinguisher Recharged Today
Skip the service call and drive to our St. Petersburg facility — no appointment needed, no trip fees, no waiting around. We recharge while you wait or swap you out on the spot with a unit of similar condition that fits the same bracket — fully charged, tagged, and certified in one visit.
See the pricing table above for rates. Most recharges start at $25 and are done in under 10 minutes.
Address: 3200 62nd Ave N, St. Petersburg, FL 33702 — just off I-275
Phone: (727) 620-3473
Email: Info@ServicedFireEquipment.com
Walk-ins welcome during business hours Monday through Friday.